During a used car test drive, check how the engine starts, how the gearbox shifts, and how the car steers, rides and brakes. Inspect it before and after driving, try it on a suitable mix of roads, and ask an independent mechanic to investigate any faults before you commit to buying.
What to check before a used car test drive
Ask the seller not to start the engine before you arrive. A warm engine can make starting problems, rough running or certain noises less obvious. If the engine is warm, ask why and arrange another opportunity to check a cold start.
Before you drive, confirm that you have permission and that the car has the required documents and insurance cover for the test drive. Carry a valid driving licence. Agree on a route where you can accelerate, brake, turn and reverse normally without breaking traffic rules.
- Look beneath the parked car for fresh drips, then check accessible fluid levels as instructed in the owner’s manual. Never open a hot cooling system.
- Inspect the tyres for cuts, bulges and uneven wear, including the inner edges where you can see them.
- Adjust the seat and mirrors, fasten your seat belt, and check that you can reach the pedals comfortably.
- Test the lights, indicators, horn, wipers, windows, locks and air conditioning while the car is stationary.
- Check that the warning lights come on during the ignition self-check and go out after starting as specified in the owner’s manual.
Tyre condition and pressure can affect how the car drives. The National Highway Traffic Safety Administration recommends checking tyre pressure against the vehicle manufacturer’s specification, not the maximum pressure shown on the tyre sidewall. If any tyres look unsafe, have them assessed before you drive.
What to check when starting a cold engine
Start the engine without pressing the accelerator unless the owner’s manual instructs otherwise. Notice whether it turns over easily, starts promptly and settles into a steady idle. If it needs repeated attempts, takes too long to start or stalls, have it checked. A test drive alone cannot tell you the cause.
Listen with the audio system off. Distinguish a brief sound at start-up from persistent knocking, rattling or squealing. Ask the seller about unusual noises, but get a mechanic’s diagnosis rather than relying on the seller’s explanation.
Watch for persistent exhaust smoke. Blue smoke can indicate that the engine is burning oil, while persistent, dense white smoke after the engine warms up can indicate a coolant-related fault. Brief water vapour at start-up is not, by itself, proof of engine trouble.
Switch on the air conditioning and check that it cools properly without causing excessive vibration or stalling. Some change in the engine sound is normal as the compressor operates. If you notice a strong smell of fuel, burning oil or coolant, find out what’s causing it before you continue.
How to test the clutch and gearbox
In a manual car, pull away normally and check that the clutch engages smoothly and progressively. Have a mechanic check any judder, difficulty selecting gears or unusually heavy clutch pedal. A high biting point alone does not prove that the clutch needs replacing.
Shift through the gears at suitable speeds. You should be able to select each gear without grinding, and the gearbox should not jump out of gear. Under normal acceleration, rising revs without matching acceleration can suggest clutch slip. Don’t deliberately strain the clutch or attempt a high-gear stall test.
In an automatic, select drive and reverse while stationary, keeping the brake pedal pressed. Watch for a pronounced delay, heavy thump or failure to engage. During the drive, check for shuddering, loss of drive or surges in engine revs without a corresponding increase in speed.
Judge the transmission according to its design. An automated manual can pause between shifts, while a CVT can hold higher engine revs during acceleration. If you’re unsure whether something is normal or a fault, ask a mechanic familiar with that transmission to check it.
How to check the steering, suspension and brakes
On a reasonably level, straight road, keep both hands on the wheel and notice whether you need to make constant corrections to keep the car straight. Don’t release the wheel to test alignment. Have a mechanic investigate persistent pulling, an off-centre steering wheel or excessive play in the steering.
Take ordinary bends and drive slowly over speed breakers. Listen for knocks or clunks and notice whether the car keeps bouncing after a bump. Suspension wear, tyre problems and loose components can produce similar symptoms, so don’t assume a particular part is faulty based on noise alone.
Test the brakes gradually where you have clear space and no vehicle close behind. The pedal should feel consistent, and you should be able to slow the car predictably without it pulling sharply to one side. Have a professional inspect any pedal pulsation during routine braking, grinding noises or a sinking brake pedal.
Stop the test drive safely if the brakes or steering feel unsafe, the engine overheats, or an oil-pressure warning stays on. Pull over safely and switch off the engine where appropriate; don’t continue simply to complete the route.
Which roads should you use for a test drive?
Choose a route that reflects how you’ll use the car. A short loop at low speed may not reveal vibration, hesitation or transmission problems that appear once the drivetrain warms up.
- Drive through low-speed traffic to assess clutch effort, throttle response and smoothness.
- Use a quieter open stretch for gradual acceleration and steady-speed cruising within the speed limit.
- Include an uneven but safe surface to check ride comfort and suspension noise without deliberately hitting potholes.
- Reverse into a parking space to check visibility, steering assistance, parking sensors and the camera, if fitted.
Keep the audio system off for most of the drive. Note whether a noise changes with road speed, engine revs, braking or turning. These details will help a mechanic investigate it.
What to check after a used car test drive
Park safely and check for fresh leaks, unusual smells or new warning lights. You may see clear water dripping from the air-conditioning drain, which can be normal. Don’t touch hot engine or exhaust components.
Compare any faults you noticed with the service records and ask for invoices to support the seller’s claims about repairs. Check that the odometer reading is consistent with the service records, but don’t take a trouble-free drive as proof of genuine mileage or an accident-free history.
Arrange an independent pre-purchase inspection before paying a non-refundable amount. Ask for an underbody inspection, a diagnostic scan and checks for any symptoms you noticed. Get written repair estimates, and don’t proceed if safety-related faults remain unexplained or the seller refuses to allow an independent inspection.